Garage floor insulation, Po angielsku
[ Pobierz całość w formacie PDF ]
Ron insulated between the rafters
and installed a workshop/garage
heater in his workshop, but the
concrete slab still remained really
cold. Ron decided to install a new
insulated floor system, as well.
The first step is to clear everything
out and sweep the floor clean.
The sub-flooring material Ron
used is a product called DRIcore.
This is an engineered wood
product made up of wood chips or
flakes that are compressed under
high pressure using waterproof
glue. On the back side of each
panel is a polyethylene moisture
barrier.
When using this product, it is important to bring it inside at least 24
hours before installation. This will allow the material to acclimate to
both the temperature and the humidity in the room.
The sub floor comes in two-foot
squares that interlock with each
other using tongue in groove
joinery. Glue is not used in this
floor system.
This is called a floating floor
system, which means it is not
attached to the concrete
underneath, but instead sits or
floats on top. This entire floor
expands and contract with
changes in humidity and
temperature, which means you
need to use spacers around the
edges of the floor to create a
quarter inch gap. When the floor
installation is complete, the
spacers can be removed so that
the gap enables the floor to move
as it needs to.
After each tile is set in place, set a
tapping block on the edge of the
panel and tap it gently with a
hammer to secure the joint firmly
together.
If your existing floor is uneven,
use a straight edge to locate the
low spots, which will create a gap
underneath the straight edge.
The floor panels are easily
adaptable to these irregularities
with simple shims that are
designed to fit over the molded
panel bottoms. If necessary, you
can stack up to four of these on
top of each other. Masking tape
helps hold the shims in place
when you flip the panels over.
When you come to the end of
your first row, you will probably
need a piece smaller than a full
panel to fill the remaining space.
Simply measure the space, set
your table saw fence to the
required dimension, and then
make the cut. A hand held circular
saw or jigsaw can also be used to
make these simple cuts.
The cut piece drops into place,
but you will not be able to use a
hammer and tapping block to
tighten up the joint. Instead, use a
tool called a pinch bar, which slips
into the gap next to the wall and
hooks over the edge of the panel.
The opposite end is bent upward
to form a striking surface. A few
hammer blows brings the joints
tightly together. Begin the second
row by staggering the joints so
that they fall directly in the center
of the boards of the first row.
Staggering the rows in this way
creates a much more stable floor.
When working in a doorway, you
will need to notch out a panel to fit
around the corner.
The easiest way to do this is to
set the panel in place and then
use a straight edge or square to
extend the wall lines onto the
board.
A jigsaw makes cutting out the
notch quick and simple.
Not only does this floor go in
quickly and easily, but it also
looks good. It is an ideal sub-floor
for wood, carpet, vinyl or laminate.
Because Ron was installing his
floor in a garage and workshop he
decided on something called the
G-floor from Better Life
Technologies for his floor surface.
This garage floor covering comes
in nine-foot widths and simply rolls
out, but it lies perfectly flat and
stays in place without the need for
adhesive.
In just a couple of minutes, this
material transforms the look and
feel of the entire floor.
To trim the edges, use either a
hook shaped utility knife blade, or
a pair of scissors. Simply cut the
floor to fit as you work your way
around the edge of the room. To
hold the seams tightly together,
apply double stick carpet tape to
the back of the floor.
Carefully remove the protective liner from only one side, because
you want the tape to stick only to the covering and not to the
underlayment. This leaves the floor covering free to expand and
contract with changes in temperature and humidity.
Remove any bubbles or ripples
with a push broom, working from
the center to the edges. This new
flooring is tough, durable and
good looking. If you ever plan to
park a car on this surface, it is
resistant to oil and gasoline.
The floor is not attached to
anything, so you can easily
remove it if you ever need to.
Although this new floor covering is
only about an inch thick, it still
offers a pretty good insulation
value, which can make any
workspace much more
comfortable.
[ Pobierz całość w formacie PDF ]